REMOTE CONTROL
RGB RF Wireless Controller #NT301
RGB RF Wireless Controller #NT371
RGBW RF Wireless Controller #NT471

RGB RF Wireless Remote Controller

Model # NT301

NT301 RGB RF Wireless Remote Controller is a Mini RGB controller with RF remote to control and dim any of Red/Green/Blue (RGB) LED Light Bars and Light Strips. The Remote can control any 12V DC or 24V DC RGB LED products. Several different static colors (including pure white) and dynamic color changing modes are selectable and adjustable using the remote controller. 

  • Remote
  • Receiver
Model No. NT301
Work Voltage DC 5-24V
Output 3ch X 2A
Dynamic mode 22 Modes
Speed grade10 Levels
Static Color 20 Colors
Color Brightness grade 5 Levels
Direct Color Select 6 Direct Keys
PWM Grade 256 Steps
Overload Protection Yes
Overheat Protection Yes
Remote Frequency 433.92 MHz
Remote Controller Distance> 15m at open area
Remote Dimension 85 X 40 X 5 mm
Controller Dimension 46 X 13 X 6 mm
Battery 3V CR2025
IP RatingIP 20

Operating Manual

  • 1. Turn On/ Standby
    Press this key to turn on unit or switch to standby mode. At power on, unit will automatically turn on and restore to previous statue.
  • 2. Dynamic Mode Adjust
    Switch to dynamic mode from static color, or switch between dynamic modes.
  • 3. Dynamic Speed Adjust
    Adjust dynamic playing speed. Press SPEED(+) to increase speed mode if press SPEED(-) to decrease. Unit will switch to dynamic mode if press this key at static color mode.
  • 4. Static Color Adjust
    Switch to static color mode from dynamic mode, or switch between static colors.
  • 5. Direct Color Select
    Shortcut key to static colors. When press the specific color key, LED will play the same static color. The direct colors are included in 'COLOR(+)' and 'COLOR(-)' operation.
  • 6. Brightness Adjust
    Adjust static color brightness. Press BRIGHT(+) to increase brightness and press BRIGHT(-) to decrease. Unit will switch to static color mode if press this key at dynamic mode.
  • 7. Demo Mode
    Press this key will switch to Demo mode. At demo mode, it plays 17 dynamic modes in loop, each mode repeat 3 times.
  • 8. Power Supply
    This unit accepts DC 5V to 24V power supply. The DC jack's inner pole (or red cable) is positive and sleeve (or black cable) is negative. Also please make sure the power supplt voltage is same as the LED load.
  • 9. LED Output
    This unit support common anode connection LED products. The mark '+' indicates the common connection node. The peak output current is 4 amperes and maximum constant current is 2 amperes per channel. Please reduce load if main unit is overheating.

    CAUTION! Do not short circuit or overload the LED outputs, this may lead to permanent demage!
  • 10. Using Remote Controller
    Please pull out the battery insulate tape before using. The RF wireless remote signal can pass throught barrier, so it's not necessary to aim at the main unit when operate.
    1) Plug off the power of main unit and plug in after 5 seconds.
    2) Press 'ON/OFF' and 'MODE+' key together in 5 seconds after power on. After this operation, the main unit will recognize any remote controller. To pair the main unit back to specific remote, please repeat the 'Pairing New Remote' operation.
  • 11. Switch Output Color Sequence
    The controller’s default output signal sequence is Common Green-Red-Blue. If the LED application is in different cable sequence, the direct color keys will not match the LED color. In this case, user can adjust the output signal sequence with following steps:
    1). Plug off the power of main unit and plug in after 5 seconds. 2). Press ‘RED’ and ‘BLUE’ color key together in 5 seconds after power on. With this operation, the output sequence will switch between 6 possible combinations. The sequence will be memorized and it won’t change before next same operation. For proper receiving remote signal, please do not install the main unit in closed metal parts.
  • 12. Pairing New Remote
    The remote and main unit is 1 to 1 paired as default. Further more, main unit can be paired to 3 remote controllers and each remote controller can be paired to any main unit. Please do following steps to pair new remote controller:
    1). Plug off the power of main unit and plug in after 5 seconds. 2). Press ‘SPEED(-)’ and ‘SPEED(+)’ key together in 5 seconds after power on. After this operation, the main unit will recognize the new remote controller.
  • 13. Free Remote Pairing Mode
    In some specific cases, the main unit may need to be paired to any remote controllers. Please do following steps for free remote pairing mode:
    1). Plug off the power of main unit and plug in after 5 seconds. 2). Press ‘COLOR(-)’ and ‘BRIGHT(-)’ key together in 5 seconds after power on.
.