RGBW RF Wireless Remote Controller

Model # NT471

NT471 RGBW RF Wireless Remote Controller is designed to drive constant voltage LED products with common anode connection in voltage range of DC5-24V. The Controller works with a RF remote, user can set white LED brightness, RGB LED color, brightness and dynamic modes on the remote. The Controller is powered by DC power supply and receives remote commands to drive LED fixtures.

  • Remote
  • Receiver
Model No.NT471
Work VoltageDC 5-24V
Output 3ch X 3A (RGB) + 5A (W)
Dynamic Mode 34 Modes
Speed Grade 10 Levels
Static Color30 Colors
Color Brightness Grade 5 Levels
Direct Color Select 6 Direct Keys
PWM Grade 4,000 Steps
Overload Protection Yes
Overheat Protection Yes
Remote Frequency433.92 Mhz
Remote Control Distance> 15m at open area
Remote Dimension 87 X 36 X 8 mm
Controller Dimension 87 X 24 X 15 mm
Battery 3V CR2032
IP Rating IP 20

Operating Manual

  • 1. Power Input
    Install positive power cable into the terminal marked with ‘+’ and negative power cable into the terminal marked with ‘-’. The two positive jacks are connected inside the Controller and same for the negative jacks. The Controller can accept DC power from 5V to 24V, the output voltage is the same as the power supply, so please make sure the LED rated voltage is same as the power supply. Do not power on the Controller until all connection is firmly finished.
  • 2. LED Output
    Connect LED RGB Strip to this terminal. Install LED common anode cable into the terminal marked with ‘+’ and each channel LED cables into the terminal marked with R, G, B. Please make sure the LED rated voltage is same as the power supply and each channel’s maximum load current is below the controller rated current.
    The controller will run into protection if the output been overloaded or short circuited. The indicator will flash red color and stop working in this case. Please check the wiring and load current to remove the fault.
  • 3. Turn ON / OFF
    Press 'I' key to turn on Controller or press 'O' key to turn off. Controller will memorize the on/off status and will restore to the previous status on next power on. Please use remote to turn on the unit if it was switched to off status before previous power cut.
  • 4. White LED control
    Press 'WHITE ONLY' key to switch off RGB and only use white LED channel. The white LED brightness could be adjusted independently by the two white brightness adjust keys on the right side of 'WHITE ONLY' key.
  • 5. RGB mode and brightness
    Press 'COLOR ONLY' key to switch off white and only use RGB LED channels. The static color brightness could be adjusted by the two color brightness keys on the right side of 'COLOR ONLY' key.
  • 6. Select static RGB color
    These keys set the RGB static color. Press the colored keys to set the RGB LEDs to correspond color. For other colors, please press 'COLOR+' and 'COLOR-' key to select from the preset library colors.
  • 7. RGB dynamic mode
    These keys control the RGB dynamic modes. Press 'MODE+' and 'MODE-' to select dynamic modes and press 'SPEED+' and 'SPEED-' key to set the running speed of the dynamic modes.
  • 8. Remote Indicator
    This indicator blinks when remote works. The indicator will flash slowly if the battery is empty, please change the remote battery in this case. The battery model is CR2032 lithium cell.
  • 9. Using the remote
    Please pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the Controller in closed metal parts.
  • 10. Pairing a new remote
    The remote and Controller is 1 to 1 paired for factory default. It’s possible to pair maximum 5 remotes to one Controller and each remote could be paired to any Controller.

    You could pair a new remote to Controller by following steps:
    1). Plug off the power of Controller and plug in again after more than 5 seconds.
    2). Press’ COLOR ONLY’ and ’ color brightness plus ‘ key simultaneously for about 3 seconds, in time of 10 seconds after the Controller powered on.

    In some cases, one Controller might be paired with several remote but extra remotes are no longer needed. User could simply pair the current using remote to Controller again, then the Controller will dis-pair all other remotes and recognize current one only.
  • 11. Protection
    The Controller has full protection function for wrong wiring, output short circuit, overload and overheat. The Controller will protect itself from damage at these extreme conditions and could automatically recover when working condition is good. To avoid the protection, please ensure the LED Strip are capable for constant voltage driving and in rated range, the cables are well connected and insulated. Please also install the Controller with good ventilation and heat dissipation condition.
  • 12. Work Statue Indicator
    This indicator displays all working status of the Controller. It shows different events as following:
.